VC Switch Release:
- Accessory for circuit breakers PR 60, PR 60J, PRe 60, modular switch RV 60, and protectors PFI, PFB.
- Used to switch off the circuit breaker (switch) using an external voltage source, with an immediate disconnection of the circuit.
- Supplied as a standalone unit or together with the circuit breaker (switch).
- Mounted on the right side of the circuit breaker (switch), left side of the protector using pins and screws.
Under-voltage release PC:
- Accessory for PR 60, PR 120, RV 60, RV 120.
- Used to protect against motor restart during a voltage outage.
- Signaling the release position in green/red.
- Auxiliary button for checking the correct function.
- Factory installation on circuit breakers.
Auxiliary signaling contacts PKJ, 2PKJ, PKJ+SKJ:
- Accessory for circuit breakers PR 60, PR 60J, PRe 60, modular switch RV 60, and current protector.
- Supplied as a standalone unit or together with the circuit breaker (switch).
- Mounted on the left side of the circuit breaker (switch) using pins and screws.
- Used to signal the status of the circuit breaker (switch).
N-pole:
- Installed at the factory according to customer requirements.
- The N-pole can be connected to all AC versions (current values, characteristics) of circuit breakers PR 61 and PR 63.
- The N-pole has no release; it closes earlier when the circuit breaker is turned on and opens later when turned off than other poles.
- When ordering the N-pole, specify the type and item number of the circuit breaker and the type and item number of the N-pole.
Translucent covers KSP1 and KSP3:
- Accessory for circuit breakers PR 60, PR 60J, PRe 60, and modular switch RV 60.
- Used to increase protection to IP 30 and for sealing terminals with a sealing plug.
- The single-pole cover of terminals KSP 1 does not increase the width of the breaker's module (switch); 2 covers are needed to cover both terminals.
- The three-pole cover of terminals KSP 3 is applicable only for PR 63 and RV 63, with the width of the three-pole version changing from 52.5 mm to 57 mm.
- Plugging the cover onto the breaker requires a sealing plug PZ.
Locking lever - UP:
- Accessory for circuit breakers PR 60, PR 60J, PRe 60.
- Used for safely locking the lever in the on or off position of the circuit breaker (switch) using a hanging lock with a maximum shackle diameter of Ø 4.5 mm.
- UP1 slides from the right onto the lever of the circuit breaker (switch). For multi-pole circuit breakers (switches), it is applied to the right pole.
- The breaker locked in the on position does not lose its tripping function.
Sealing plug:
- Accessory for circuit breakers PR 60, PR 60J, PRe 60, and modular switch RV 60.
- Used for sealing individual terminals, single-pole terminal covers KSP1, three-pole terminal covers KSP3, and for securing three-pole terminal covers KSP3.
- A sealing wire with a maximum diameter of 0.1.5 mm can be used for sealing.
Terminals:
- Accessory for circuit breakers PR 60, PR 60J, modular switch RV 60.
- The flexible clamp for PPL rail and the clamp for PL rail are used to attach circuit breakers (switches) to the DIN 35x7.5 rail panel.
- The clamp for PP panel is used to secure circuit breakers (switches) to the panel using screws M4 or M5. Two PP panel clamps are required to attach one device to the panel.
- The basic version of circuit breakers (switches) is supplied with PL rail clamp and flexible PPL rail clamp.
- Terminals can be replaced by simply sliding and sliding the clamps.
